Race Sim Central
Rec.Autos.Simulators Archive

Have You Replaced Your ECCI CDS2 Wheel Cable?

6 posts by 2 people · 14 Jun 2003 19:35 UTC - 16 Jun 2003 11:07 UTC

Larry Lindstrom 14 Jun 2003 19:35 UTC#65822
Hi ECCI Users, and all: The button I use to upshift is intermittent. I've replaced it, from a local source, and the problem persists. ECCI recommended replacing both wheel and pedal cables, so I got both from them. I've replaced the pedal cable yesterday, that operation seems to have been successful. This morning I replaced the wheel cable. Not well apparently, I'm getting a "Not Connected" when trying to set up the wheel through the Control Panel. The instructions seem a little vague. There are 9 wires in the CDS4000's cable, and instructions for connecting 7 of them. The problem stems from the fact that the replacement cable is for a different controller, a CDS4000. Instructions for using this cable with a CDS2 are shipped with the cables. The CDS4000 cable has 9 wires, 6 terminate in a socket, 3 other wires have separate connectors. . The socket is to be cut off and the wires soldered to to wires from the CDS3's cable to the joystick port. A blue and a brown wire carries the signal from the CDS2's photometer to the joystick connector. These are to be soldered to the yellow and purple wires, respectively, from the 6 that were in the CDS4000's socket. The strange part is that the CDS4000 cable has a blue and a brown wire that are not connected with the 6 wire socket. The paragraph that instructs to cut off the socket finished with "BE CAREFUL TO AVOID CUTTING THE BLUE AND BROWN POT WIRES". The caps are theirs. Do NOT cut these wires. Nothing else is said about these mysterious brown and blue wires. Are they to replace the CDS2's blue and brown wires on the pot? If so, why did I solder those two wires to the yellow and purple wires in the CDS4000 cable? It's Saturday, about noon. I'm counting on you to help me get online tonight. Thanks Larry
In article <[email hidden]>, Larry Lindstrom <[email hidden]> writes:
Quoted text (22 lines)> A blue and a brown wire carries the signal >from the CDS2's photometer to the joystick >connector. These are to be soldered to the >yellow and purple wires, respectively, from >the 6 that were in the CDS4000's socket. > > The strange part is that the CDS4000 cable >has a blue and a brown wire that are not >connected with the 6 wire socket. The paragraph >that instructs to cut off the socket finished >with "BE CAREFUL TO AVOID CUTTING THE BLUE AND >BROWN POT WIRES". The caps are theirs. Do NOT >cut these wires. > > Nothing else is said about these mysterious >brown and blue wires. > > Are they to replace the CDS2's blue and brown >wires on the pot? If so, why did I solder those >two wires to the yellow and purple wires in the >CDS4000 cable? >
I have a CDS 4000 and after taking a look, it sounds as if your instructions are screwy. Blue and brown go to the pot, and the rest (including a yellow and a purple) go to a 6 position Berg connector which hooks to another cable that goes up the wheel shaft to the buttons. I also suspect that your problem lies within the cable which travels up the column to the wheel hub, I had the same thing about a year ago. Don McCorkle
Woodie 83 wrote: > > In article <[email hidden]>, > Larry Lindstrom <[email hidden]> writes: < Snip >
Quoted text (16 lines)> > Nothing else is said about these mysterious > >brown and blue wires. > > > > Are they to replace the CDS2's blue and brown > >wires on the pot? If so, why did I solder those > >two wires to the yellow and purple wires in the > >CDS4000 cable? > > > > I have a CDS 4000 and after taking a look, it sounds as if your instructions > are screwy. Blue and brown go to the pot, and the rest (including a yellow and > a purple) go to a 6 position Berg connector which hooks to another cable that > goes up the wheel shaft to the buttons. > > I also suspect that your problem lies within the cable which travels up the > column to the wheel hub, I had the same thing about a year ago.
Thanks Don: Yea, you are right. Replacing the original wires for the pot with those in the CDS4000 cable get the pot connected and the wheel/pedal recognized by the control panel. Unfortunately, now I have only one button that works. Troubleshooting this would be simpler if I hadn't shrink wrapped those solder joints. Yea, this is what I wanted to do all Saturday. I appreciate your assistance. Larry
Hi Again: My wheel is working as well as it was. My problem was caused by me clipping the cable between wheel and gameport, inside the wheel housing and matching that up with the CDS4000 cable. I didn't realize the harness inside the wheel had different color wire. Anyway, it's this internal harness that must be bad, because the original problem, both buttons on the right side are intermittent. So I'll try to get the components to get the internal harness from ECCI. It's basically a 6, or 7 wire shielded cable cable. Fry's is willing to sell me a thousand feet. I'm hoping ECCI will sell, or give, me a couple of yards. Thanks Larry
In article <[email hidden]>, Larry Lindstrom <[email hidden]> writes:
Quoted text (9 lines)> Anyway, it's this internal harness that must be bad, >because the original problem, both buttons on the right >side are intermittent. > > So I'll try to get the components to get the internal >harness from ECCI. It's basically a 6, or 7 wire shielded >cable cable. Fry's is willing to sell me a thousand feet. >I'm hoping ECCI will sell, or give, me a couple of yards. >
That's what I suspected, it breaks inside the wheel shaft, where it flexes constantly. I bought a huge roll of sutable wire at Radio Shack for about ten dollars, but it's solid core wire instead of braided. Worked fine for six months until I got the proper part from ECCI. Don McCorkle

Sponsors

Affiliate Links

Sim Gaming Expo MOZA Racing Sim-Lab Fanatec TrakRacer Asetek Internet Privacy From NordVPN Dreamhost Capital One Credit Card Application Fanatical CDKeys Amazon Amazon UK Project Motor Racing iRacing Get your racing gloves, boots and more from Demon Tweeks. Enlist at Roberts Space Industries, developers of Star Citizen and Squadron 42


Back from the ashes since July, 2019. First created in 2001 with the merger of Legends Central (founded 1999) and simracing.dk.

A site by a sort of sim racer, for sim racers, about racing sims. News and information on both modern and historic sim racing software titles.

All products and licenses property of their respective owners.


Facebook Threads Bluesky Twitter Mastodon Instagram YouTube Tiktok Twitch Reddit Google News Apple News Subscribe via WordPress Flipboard eBay

Race Sim Central © 1999-2026 | Some links pay RSC a commission. Advertising does not equal endorsement.Cookie Policy