What I am looking for here is the name for the device to measure
resistance, is it Multimeter?
I am still puzzled why I the CH Pedals will not work properly when
wired to the MSFF. Someone suggested the pots may different resistance
and I should buy some with the same.
I have tried using the LWFF pots, the Ch pots and the result is always
the same. It works but the length of the pedals are just as short as
the MSFF once wired into the MSFF.
I use the LWFF for GPL but I still have to use the MSFF for other sims
as I don't like the CH Pedals wired into the LWFF as USB doesn't give
me the same precision as the PDPI does
Another guy suggested finding a program that tells windows that the
pots on MSFF have more length, but I doubt you can do that sort of
thing through software, or can you?
Another thing that its been burning in my mind for a long time: Is
there a way to connect the LWFF to the PDPI L4?
That would be the perfect solution for me in GPL at the moment, or is
it not possible?
Any advice from you GPL electronics experts out there?
Many thanks.
Mauricio.
While we are on the subject of pots..
In GPL while in neutral if I press the gas very slowly, The RPMs will
slowly rise from 1500 (?) RPMs to 2100. Then it'll take a nose dive to
0 and back up to 1500. As I continue to pres the gas, The RPMs will
jump from 2200 to 2400 and then continue correctly. This happened on my
Thrust Master T1, T2, T3, CH, and home built. So it's not a matter of
dirty pots.
One note.. I do have the travel lengthened a bit on all of these. So,
Is there a set figure that the game ports recognizes? I.E. no matter
where the ohms start, it's always a range of say 250 ohms, anything over
that it'll start over again? Or is it specific to the game port? What?
I can adjust the travel length but if I didn't have to...
It's a real sun of a gun to roll the gas only to find a spot where the
engine missfires then continues smoothly.
--
=========================================
Mike Barlow of Barlow Racing?
=========================================
http://members.xoom.com/BarlowRacing/
Racing online with the help of......
Race Communications Association
Holodyne Engineering
Mystic Music
(have Your !!Name/Address!! placed here)
erm,this is a long shot,but have you considered the deadzone?
if your pedals are split and non centred ,the deadzone will appear in the
middle of the pedal range ,i have seen this myself and i don't think
dxtweaker has solved the problem (ie; setting the deadzone to 0 does not
affect a solution)
wierd huh?
evphelps
Where do I get DX Tweaker?
Slot
Actually Mike, the symptoms you described sound exactly like dirty pots. I'd
be surprised if they weren't dirty on all 5 of your controllers. Probably
spending a buck and a half for some turner cleaner at Radio Shack would be
worth a shot. You'll need it later anyway. Give it a try.
Slot
What you need is an ohm meter, easiest to find in a common Multi Meter aka
multi tester. I think the LWFF is USB or serial, so it won't work with the
PDPI.
Slot
Quoted text (15 lines)
> Actually Mike, the symptoms you described sound exactly like dirty pots. I'd > be surprised if they weren't dirty on all 5 of your controllers. Probably > spending a buck and a half for some turner cleaner at Radio Shack would be > worth a shot. You'll need it later anyway. Give it a try. > Slot > > While we are on the subject of pots.. > > This happened on my > > Thrust Master T1, T2, T3, CH, and home built. So it's not a matter of > > dirty pots.Mike, in that case I'd say gameport limitations. I don't think you'll find a
cure, but if you do, don't forget to share it with us.
Slot
> > Actually Mike, the symptoms you described sound exactly like dirty pots. I'd
> > be surprised if they weren't dirty on all 5 of your controllers. Probably
> > spending a buck and a half for some turner cleaner at Radio Shack would be
Quoted text (35 lines)
> > worth a shot. You'll need it later anyway. Give it a try. > > Slot > > > While we are on the subject of pots.. > > > This happened on my > > > Thrust Master T1, T2, T3, CH, and home built. So it's not a matter of > > > dirty pots. > It does sound just like dirty pots. But! this is with new pots and > old pots. Right at the same place. When I adjust the throw of the gas > peddel I don't get that at all, but I'd rather have that extra bit. > When I first noticed this I did go out and grab some > cleaner/lubricant. That didn't do the trick, so I went out and grabbed > some new pots. Again, that didn't do the trick. So, It has to be > either the Sim limitations or the game port limitations. > Mike > -- > ========================================= > Mike Barlow of Barlow Racing? > ========================================= > http://members.xoom.com/BarlowRacing/ > Racing online with the help of...... > Race Communications Association > Holodyne Engineering > Mystic Music > (have Your !!Name/Address!! placed here)On Mon, 10 Jan 2000 19:59:18 -0000, "In2home User"
No. The deadzone is not an issue here as only about 60% of the pedal
travel is available. Surely it must be something to do with the
resistance.
Cheers
Mauricio.
Download and run DXTweak, watch what happens to the pedal range while
moving the pedal thro full travel.
It should just rise all the way/ or fall with no jumps od dead spots.
You are sure that you are not running the pot over the end stop and
accross the "no resistance" part of the track in it??
Try an arc on the pot starting from a different point, do it with your
hand with the pot disconnected from the pedal and see what happens.....
MikeT.
--
