Race Sim Central
Rec.Autos.Simulators Archive

Homemade wheel question...

13 posts by 9 people · 23 Apr 1999 - 26 Apr 1999

schwab 23 Apr 1999#463602
Ok, this is to anyone with a homemade wheel that gets Windows to recognize it: I finally built my homemade steering wheel and it's nice. But because of time constraints, I picked up some CH Pedals to use with the wheel. For the wheel, I am using a Radio Shack 100K linear-taper pot. Intially, in DOS utils like Jcenter.exe, it steered backwards (right goes left, etc). I had center lug on the pot going to pin #1, like suggested. I had the left lug (when looking down the shaft at the pot) wired to #3. That's when it was going "backwards" in the DOS utils. I switched it to the right lug and it steered as expected. (Note: all of the other wires in the J-stick cable are not connected, with the exception of #1 and #3 (steering) and Pins 2, 4 and 7 for the shifters. The remaining wires and pins are still present in the plug, but they are not connected to anything) But left lug or right lug on Pin 3, Windows 95 would not recognize it... with the exception of "Thrustmaster T2 without adapter." Then the calibrate button would come on, but it would not calibrate correctly... the pedals were not right. So how I have it setup is the pedals attatched directly into the gameport on my SB Live card. The CH Pedals have a built-in "Y" connector to plug the second wheel (or stick) into. The problem I'm having is in calibrating the wheel in Windows. With Jcenter.exe and other DOS utils, I can see all axes and they seem to work fine. Also, the shifters work fine (done like the Wally shifter design). What makes it strange, too, is that I am able to remove the wheel, put my old CH Flightstick into the "Y" and then find and calibrate it instantly and correctly as a 3-axis 2-button stick. I can then calibrate the stick and pedals correctly as split axis. It works absolutely fine in Grand Prix Legends. But my homemade wheel is what I want to use... just can't at the moment. I have tried the ProPanel, but still no luck. Any suggestions would be most appreciated. Thanks for your time and help, -_Dave Schwabe -- Dave Schwabe The Aussie Toad -- Grand Prix Legends & Brabham site http://users.wi.net/~schwabe
Hi Dave! Are you sure that 100K is the right pot-size? I measured my TM F1 wheelpot the other day and it was a 220K-type... Just a thought. Bye! Crash erika.und.joachim.blum.vcf < 1K Download
100K Ohm is correct. ~200K Ohm also work, but take longer to read. Randy
Jarn 23 Apr 1999#463605
maybe you got the wheel on the same axis as the CH pedals to check this out you can connect the wheel to pin 9 and 11. then your wheel is on a different axis greetings , Jarno
Quoted text (7 lines)> Ok, this is to anyone with a homemade wheel that gets Windows to > recognize it: > I finally built my homemade steering wheel and it's nice. But because of > time constraints, I picked up some CH Pedals to use with the wheel. > F
schwab 23 Apr 1999#463606
Good thought, Jo... that might be part of the problem. I will research whether or not the ohm-age of the pot is crucial to Windows recognizing it. Thanks! :-) -_Dave
Quoted text (8 lines)> Hi Dave! > Are you sure that 100K is the right pot-size? I measured my TM F1 wheelpot > the other day and it was a 220K-type... > Just a thought. > Bye! > Crash
-- Dave Schwabe The Aussie Toad -- Grand Prix Legends & Brabham site http://users.wi.net/~schwabe
schwab 23 Apr 1999#463607
Another good suggestion... Thanks Jarno! :-) I will experiment... -_Dave
Quoted text (17 lines)> maybe you got the wheel on the same axis as the CH pedals > to check this out you can connect the wheel to pin 9 and 11. > then your wheel is on a different axis > greetings , > Jarno > > Ok, this is to anyone with a homemade wheel that gets Windows to > > recognize it: > > I finally built my homemade steering wheel and it's nice. But because of > > time constraints, I picked up some CH Pedals to use with the wheel. > > F
-- Dave Schwabe The Aussie Toad -- Grand Prix Legends & Brabham site http://users.wi.net/~schwabe
Trips 23 Apr 1999#463608
Here's the answer you're looking for... The CH pedals occupy axes 3 and 4, and Win95 expects a joystick to occupy axes 1 and 2. When you plug your homemade wheel into the pedals, Win95 sees axes 1, 3, and 4, and it will not let you calibrate unless it sees an axis2. The Thrustmaster Nascar Pro wheels when switched to separate axes place the gas pedal on axis 2 and the brake on axis 4, so Windows can recognize it as a 2 axis 4 button with rudder pedals just fine. There are two solutions for you... First, you can wire another pot (or just a dummy 100K resistor) into your wheel connected to axis 2, then Windows will see it and allow you to calibrate the wheel and pedals. The other solution would be to rewire the gas pedal of your CH set to axis 2. That would , however render the CH pedals useless for flight sims. Best and easiest solution would be to add a 100K pot to your wheel, wired to the Y axis just so Windows can see it and not think there's a missing axis. Trips D. Bell on VROC
Quoted text (52 lines)> Ok, this is to anyone with a homemade wheel that gets Windows to > recognize it: > I finally built my homemade steering wheel and it's nice. But because of > time constraints, I picked up some CH Pedals to use with the wheel. > For the wheel, I am using a Radio Shack 100K linear-taper pot. Intially, > in DOS utils like Jcenter.exe, it steered backwards (right goes left, > etc). I had center lug on the pot going to pin #1, like suggested. I had > the left lug (when looking down the shaft at the pot) wired to #3. > That's when it was going "backwards" in the DOS utils. I switched it to > the right lug and it steered as expected. > (Note: all of the other wires in the J-stick cable are not connected, > with the exception of #1 and #3 (steering) and Pins 2, 4 and 7 for the > shifters. The remaining wires and pins are still present in the plug, > but they are not connected to anything) > But left lug or right lug on Pin 3, Windows 95 would not recognize it... > with the exception of "Thrustmaster T2 without adapter." Then the > calibrate button would come on, but it would not calibrate correctly... > the pedals were not right. > So how I have it setup is the pedals attatched directly into the > gameport on my SB Live card. The CH Pedals have a built-in "Y" connector > to plug the second wheel (or stick) into. > The problem I'm having is in calibrating the wheel in Windows. With > Jcenter.exe and other DOS utils, I can see all axes and they seem to > work fine. Also, the shifters work fine (done like the Wally shifter > design). > What makes it strange, too, is that I am able to remove the wheel, put > my old CH Flightstick into the "Y" and then find and calibrate it > instantly and correctly as a 3-axis 2-button stick. I can then calibrate > the stick and pedals correctly as split axis. It works absolutely fine > in Grand Prix Legends. > But my homemade wheel is what I want to use... just can't at the moment. > I have tried the ProPanel, but still no luck. > Any suggestions would be most appreciated. > Thanks for your time and help, > -_Dave Schwabe > -- > Dave Schwabe > The Aussie Toad -- Grand Prix Legends & Brabham site > http://users.wi.net/~schwabe
D&S Schwabe 24 Apr 1999#463746
That's it!!! :-) Thanks Trips! (The ever gracious and simsational Alison Hine also came to the rescue with the same recommendation) I had a pot laying around, dropped it in and wired it to pins 6 and 9 and BINGO, it got recognized. I had some wierdness when I tried calibrating it as a Thrustmaster product (mainly because the pedals are wired differently). But when I went to configure it as a three-axis with two buttons, ALL axes showed up including the "fake" Joystick A "Y" axis. But the steering and pedals calibrated fine, and I was off and running in GPL!!! Now, I must say, after being pretty damn competitive with a j-stick... it's gonna take a while. I spent some time messing with linearity and steering ratios and it was definitely different. I'm gonna have to reprogram myself! :-) But I can see how once I get used to it, things will be less tiring and the dual-axis will be much nicer in both trail braking and left-foot braking. Ultimately, it will be faster.... but time will tell. Thanks again everyone!! I was not expecting this many suggestions.... (blush) so I really appreciate it. -_dave >Here's the answer you're looking for... >The CH pedals occupy axes 3 and 4, and Win95 expects a joystick to occupy >axes 1 and 2. When you plug your homemade wheel into the pedals, Win95 sees >axes 1, 3, and 4, and it will not let you calibrate unless it sees an axis2.
Quoted text (70 lines)>The Thrustmaster Nascar Pro wheels when switched to separate axes place the >gas pedal on axis 2 and the brake on axis 4, so Windows can recognize it as >a 2 axis 4 button with rudder pedals just fine. >There are two solutions for you... First, you can wire another pot (or just >a dummy 100K resistor) into your wheel connected to axis 2, then Windows >will see it and allow you to calibrate the wheel and pedals. The other >solution would be to rewire the gas pedal of your CH set to axis 2. That >would , however render the CH pedals useless for flight sims. Best and >easiest solution would be to add a 100K pot to your wheel, wired to the Y >axis just so Windows can see it and not think there's a missing axis. >Trips >D. Bell on VROC >> Ok, this is to anyone with a homemade wheel that gets Windows to >> recognize it: >> I finally built my homemade steering wheel and it's nice. But because of >> time constraints, I picked up some CH Pedals to use with the wheel. >> For the wheel, I am using a Radio Shack 100K linear-taper pot. Intially, >> in DOS utils like Jcenter.exe, it steered backwards (right goes left, >> etc). I had center lug on the pot going to pin #1, like suggested. I had >> the left lug (when looking down the shaft at the pot) wired to #3. >> That's when it was going "backwards" in the DOS utils. I switched it to >> the right lug and it steered as expected. >> (Note: all of the other wires in the J-stick cable are not connected, >> with the exception of #1 and #3 (steering) and Pins 2, 4 and 7 for the >> shifters. The remaining wires and pins are still present in the plug, >> but they are not connected to anything) >> But left lug or right lug on Pin 3, Windows 95 would not recognize it... >> with the exception of "Thrustmaster T2 without adapter." Then the >> calibrate button would come on, but it would not calibrate correctly... >> the pedals were not right. >> So how I have it setup is the pedals attatched directly into the >> gameport on my SB Live card. The CH Pedals have a built-in "Y" connector >> to plug the second wheel (or stick) into. >> The problem I'm having is in calibrating the wheel in Windows. With >> Jcenter.exe and other DOS utils, I can see all axes and they seem to >> work fine. Also, the shifters work fine (done like the Wally shifter >> design). >> What makes it strange, too, is that I am able to remove the wheel, put >> my old CH Flightstick into the "Y" and then find and calibrate it >> instantly and correctly as a 3-axis 2-button stick. I can then calibrate >> the stick and pedals correctly as split axis. It works absolutely fine >> in Grand Prix Legends. >> But my homemade wheel is what I want to use... just can't at the moment. >> I have tried the ProPanel, but still no luck. >> Any suggestions would be most appreciated. >> Thanks for your time and help, >> -_Dave Schwabe >> -- >> Dave Schwabe >> The Aussie Toad -- Grand Prix Legends & Brabham site >> http://users.wi.net/~schwabe
Trips 24 Apr 1999#463747
Glad to be of help... Trips
Quoted text (107 lines)> That's it!!! :-) > Thanks Trips! (The ever gracious and simsational Alison Hine also came to > the rescue with the same recommendation) > I had a pot laying around, dropped it in and wired it to pins 6 and 9 and > BINGO, it got recognized. > I had some wierdness when I tried calibrating it as a Thrustmaster product > (mainly because the pedals are wired differently). But when I went to > configure it as a three-axis with two buttons, ALL axes showed up including > the "fake" Joystick A "Y" axis. But the steering and pedals calibrated fine, > and I was off and running in GPL!!! > Now, I must say, after being pretty damn competitive with a j-stick... it's > gonna take a while. I spent some time messing with linearity and steering > ratios and it was definitely different. I'm gonna have to reprogram myself! > :-) > But I can see how once I get used to it, things will be less tiring and the > dual-axis will be much nicer in both trail braking and left-foot braking. > Ultimately, it will be faster.... but time will tell. > Thanks again everyone!! I was not expecting this many suggestions.... > (blush) so I really appreciate it. > -_dave > >Here's the answer you're looking for... > >The CH pedals occupy axes 3 and 4, and Win95 expects a joystick to occupy > >axes 1 and 2. When you plug your homemade wheel into the pedals, Win95 sees > >axes 1, 3, and 4, and it will not let you calibrate unless it sees an > axis2. > >The Thrustmaster Nascar Pro wheels when switched to separate axes place the > >gas pedal on axis 2 and the brake on axis 4, so Windows can recognize it as > >a 2 axis 4 button with rudder pedals just fine. > >There are two solutions for you... First, you can wire another pot (or just > >a dummy 100K resistor) into your wheel connected to axis 2, then Windows > >will see it and allow you to calibrate the wheel and pedals. The other > >solution would be to rewire the gas pedal of your CH set to axis 2. That > >would , however render the CH pedals useless for flight sims. Best and > >easiest solution would be to add a 100K pot to your wheel, wired to the Y > >axis just so Windows can see it and not think there's a missing axis. > >Trips > >D. Bell on VROC > >> Ok, this is to anyone with a homemade wheel that gets Windows to > >> recognize it: > >> I finally built my homemade steering wheel and it's nice. But because of > >> time constraints, I picked up some CH Pedals to use with the wheel. > >> For the wheel, I am using a Radio Shack 100K linear-taper pot. Intially, > >> in DOS utils like Jcenter.exe, it steered backwards (right goes left, > >> etc). I had center lug on the pot going to pin #1, like suggested. I had > >> the left lug (when looking down the shaft at the pot) wired to #3. > >> That's when it was going "backwards" in the DOS utils. I switched it to > >> the right lug and it steered as expected. > >> (Note: all of the other wires in the J-stick cable are not connected, > >> with the exception of #1 and #3 (steering) and Pins 2, 4 and 7 for the > >> shifters. The remaining wires and pins are still present in the plug, > >> but they are not connected to anything) > >> But left lug or right lug on Pin 3, Windows 95 would not recognize it... > >> with the exception of "Thrustmaster T2 without adapter." Then the > >> calibrate button would come on, but it would not calibrate correctly... > >> the pedals were not right. > >> So how I have it setup is the pedals attatched directly into the > >> gameport on my SB Live card. The CH Pedals have a built-in "Y" connector > >> to plug the second wheel (or stick) into. > >> The problem I'm having is in calibrating the wheel in Windows. With > >> Jcenter.exe and other DOS utils, I can see all axes and they seem to > >> work fine. Also, the shifters work fine (done like the Wally shifter > >> design). > >> What makes it strange, too, is that I am able to remove the wheel, put > >> my old CH Flightstick into the "Y" and then find and calibrate it > >> instantly and correctly as a 3-axis 2-button stick. I can then calibrate > >> the stick and pedals correctly as split axis. It works absolutely fine > >> in Grand Prix Legends. > >> But my homemade wheel is what I want to use... just can't at the moment. > >> I have tried the ProPanel, but still no luck. > >> Any suggestions would be most appreciated. > >> Thanks for your time and help, > >> -_Dave Schwabe > >> -- > >> Dave Schwabe > >> The Aussie Toad -- Grand Prix Legends & Brabham site > >> http://users.wi.net/~schwabe
Trips 24 Apr 1999#463749
You don't really need a pot, a plain 100K resistor from Radio Shack will do the job. As long as the gameport "sees" resistance on both axes 1 and 2, you'll be fine. Trips D. Bell on VROC
Quoted text (15 lines)> > That's it!!! :-) > Cool, been having the same problems myself with my homemade wheel and CH > pedals, pin 6 and 9, hmm, wonder where I can get a pot on Saturdays in > this town :-) > Thx a bunch guys > -- > Beers and cheers > (uncle) Goy > "Team Mirage" http://www.teammirage.com/ > "The Pits" http://www.theuspits.com/
% > Hi Dave! % > % > Are you sure that 100K is the right pot-size? I measured my TM F1 % wheelpot % > the other day and it was a 220K-type... % > Just a thought. % 100K Ohm is correct. ~200K Ohm also work, but take longer to read. Thrustmaster uses 200K+ Ohm pots to allow their units to be more compatiable with slow and faster computers. -- **************************** Michael E. Carver ************************* Upside out, or inside down...False alarm the only game in town. =-=-=-=-=-=-=-=-=-=-=-=-=-=-=<[ /./. [- < ]>=-=-=-=-=-=-=-=-=-=-=-=-=-=
> You don't really need a pot, a plain 100K resistor from Radio Shack will > do the job. As long as the gameport "sees" resistance on both axes 1 and > 2, you'll be fine. > Trips > D. Bell on VROC You don't really need a resistor. A piece of wire (i.e. 0 Ohms) will do fine, and take fewer cpu cycles to read. OTOH, I would add a pot and make it usable as a clutch somehow. BTW, this business of needing certain axes to be present before recognising the controller must catch out nearly all the people who make their own controllers. It puzzled me for a while. My guess is it's part of a misguided attempt to let windows distinguish between different controllers automatically, i.e. so it knows when you've unplugged the joystick and plugged in the wheel. Anton -- Antony Bowers, Department of Computer Science, University of Bristol, UK. http://www.cs.bris.ac.uk/~bowers/

Sponsors

Affiliate Links

Sim Gaming Expo MOZA Racing Sim-Lab Fanatec TrakRacer Asetek Internet Privacy From NordVPN Dreamhost Capital One Credit Card Application Fanatical CDKeys Amazon Amazon UK Project Motor Racing iRacing Get your racing gloves, boots and more from Demon Tweeks. Enlist at Roberts Space Industries, developers of Star Citizen and Squadron 42


Back from the ashes since July, 2019. First created in 2001 with the merger of Legends Central (founded 1999) and simracing.dk.

A site by a sort of sim racer, for sim racers, about racing sims. News and information on both modern and historic sim racing software titles.

All products and licenses property of their respective owners.


Facebook Threads Bluesky Twitter Mastodon Instagram YouTube Tiktok Twitch Reddit Google News Apple News Subscribe via WordPress Flipboard eBay

Race Sim Central © 1999-2026 | Some links pay RSC a commission. Advertising does not equal endorsement.Cookie Policy