T2 help

I just installed a diamond monster 3d yesterday. Every thing was working great the t2 the card everything, until I played descent 2. I played had a little fun, and since I didn't know the cheat codes, plus it was 1:30 in the morn, I unhooked my sidewinder pro and reconnected my t2, which I disconnected to play descent. The thrust master pro panel says it is not connected, and the regular game controller says it is ok, but when I want to calibrate it says it is not connected properly. To test the connection after an hour and a half of fiddling with it I played icr2 in restarted dos mode and low and behold it worked fine. Does anyone have any suggestions? The sidewinder pro did and still does work fine. -- Thank you Marc Johnson

For some reason this same thing happens to me when I switch between my joystick and t2. I end up having to right click on the joystick in either game controllers (dx5), or in the propanel utility. Then click on calibrate. Sometimes I have to do this 3 or 4 times to get it to recognize it ok. I've not been able to narrow it down to 1 specific thing yet. -- Don Burnette I-65 Racing Dburn on Ten > I just installed a diamond monster 3d yesterday. Every thing was > working great the t2 the card everything, until I played descent 2. I > played had a little fun, and since I didn't know the cheat codes, plus > it was 1:30 in the morn, I unhooked my sidewinder pro and reconnected my > t2, which I disconnected to play descent. The thrust master pro panel > says it is not connected, and the regular game controller says it is ok, > but when I want to calibrate it says it is not connected properly. To > test the connection after an hour and a half of fiddling with it I > played icr2 in restarted dos mode and low and behold it worked fine. > Does anyone have any suggestions? The sidewinder pro did and still does > work fine. > -- > Thank you > Marc Johnson

Try this.. when you change sticks in Win95. Especially with Dx5. You must remove the old driver before adding the new one. Even tho the pro panel and the Controller applet and the DX5 control panel all have slots for 10 or more sticks, you can have only one listed at any one time. Always remove the old driver, then add the new one and calibrate. It's a hassle, but it should work dave henrie

Quoted text (29 lines)

> For some reason this same thing happens to me when I switch between my > joystick and t2. I end up having to right click on the joystick in either > game controllers (dx5), or in the propanel utility. Then click on > calibrate. Sometimes I have to do this 3 or 4 times to get it to recognize > it ok. I've not been able to narrow it down to 1 specific thing yet. > -- > Don Burnette > I-65 Racing > Dburn on Ten > > I just installed a diamond monster 3d yesterday. Every thing was > > working great the t2 the card everything, until I played descent 2. I > > played had a little fun, and since I didn't know the cheat codes, plus > > it was 1:30 in the morn, I unhooked my sidewinder pro and reconnected my > > t2, which I disconnected to play descent. The thrust master pro panel > > says it is not connected, and the regular game controller says it is ok, > > but when I want to calibrate it says it is not connected properly. To > > test the connection after an hour and a half of fiddling with it I > > played icr2 in restarted dos mode and low and behold it worked fine. > > Does anyone have any suggestions? The sidewinder pro did and still does > > work fine. > > -- > > Thank you > > Marc Johnson

Marc, I've had similar problems from time to time with a CH FF joystick when I swith to a T1 controller. Go into Control Panel, then System, then Device Manager, then go into the properties tab for your sidewinder pro. Uncheck orginal configuration, then restart your computer. This should free up system resources. Unselect sidewinder pro then select your T2. When you want to reuse the sidewinder, unselect the t2, recheck orginal configuration in the control panel for the sidewinder. Then reselect the sidewinder in propanel. I may not have this order EXACTLY right but I know if you unconfigure the controller in System and reboot resources are freeded up.

Quoted text (16 lines)

>I just installed a diamond monster 3d yesterday. Every thing was >working great the t2 the card everything, until I played descent 2. I >played had a little fun, and since I didn't know the cheat codes, plus >it was 1:30 in the morn, I unhooked my sidewinder pro and reconnected my >t2, which I disconnected to play descent. The thrust master pro panel >says it is not connected, and the regular game controller says it is ok, >but when I want to calibrate it says it is not connected properly. To >test the connection after an hour and a half of fiddling with it I >played icr2 in restarted dos mode and low and behold it worked fine. >Does anyone have any suggestions? The sidewinder pro did and still does >work fine. >-- >Thank you >Marc Johnson