Race Sim Central
Rec.Autos.Simulators Archive

T2 Steering Potentiometer Replacement

8 posts by 5 people · 12 Aug 1996 - 15 Aug 1996

Can anyone please help me with instructions on how to change the steering potentiometer in a T2. It seems to have a big barbed clip fixed in place to hold it in position and I couldn't see how to remove it. Thanks in advance, Scott
: Can anyone please help me with instructions on how to change the steering : potentiometer in a T2. It seems to have a big barbed clip fixed in place : to hold it in position and I couldn't see how to remove it. Any tips on the bungee cords on a T1 also? Thanks...Chuck
an.. 14 Aug 1996#333522
>Can anyone please help me with instructions on how to change the steering >potentiometer in a T2. It seems to have a big barbed clip fixed in place >to hold it in position and I couldn't see how to remove it. >Thanks in advance, >Scott
an.. 14 Aug 1996#333523
>Can anyone please help me with instructions on how to change the steering >potentiometer in a T2. It seems to have a big barbed clip fixed in place >to hold it in position and I couldn't see how to remove it. Scott, I just redid mine too, it's a little tricky.. I'll try to remember how I did it best I can 1. Remove the steering wheel 2. Open the case 2a. remove the BASE of the unit from the face of the T-2 3. Remove the 4 screws that hold the "neck?" in place (these***are covered in the reddish 'locktite' substance) (the neck and bunjie cord and all is one assemby it wont fly (apart on you or anything) 4. take note of the wiring on the old potentiometer 5. DO NOT attempt to disassemble the bunjie cord setup leave that in place. 6. take a small screwdriver and place it behind the old "pentometer" <--short spelling :) 7. You need to take both hands, and pull on the round thingamajig the bunjie cord rolls on, by pulling on it you will lift the steering shaft up off of the old pentometer. 8. Then use your 3rd. hand <G> to GENTLY use the screwdriver to kind of 'pry' and I use THAT term loosly, to wiggle the old one out of place. Obviously you need to use extreme caution doing this if that bottom clip snaps off your in deep ka-ka! But the graphite like material that the assembly is composed of is pretty sturdy I wouldn't wanna chance it. 9. Make sure you CENTER the new pentometer before slipping it in there. To do this take the new one in your hand and "work" it thru it's full range of motion and get the feel of the total travel. then flip it upside down and notice the "slit" or "notch" in it, it should be parallel from top to bottom. it is now centered. 10. without knocking it out of proper alignment slip the new one back in there, I had to give mine a little nudge to pop it in there, but it didn't hurt anything. Notes: Resolder the new wires on the pentometer and dont get lazy and twist them on!! Do it right and Solder them it'll save you aggrivation later on. It's a good idea to "map" ALL the wiring in there before you s start I had one or two wires break loose from their soldering points while I tried to figure this puzzle out. This way at least you wont be "guessing" later. Before reassembly make sure you clean off all that red locktite off the threads. Re-apply a drop of loc-tite on each stud if you want. (loc-tite can be found at any reputable autoparts store and some 7-11's) Most of all ... BE PATIENT this will seem tedious but frustration leads to broken parts that end up next to the old joystick,keyboard and toaster oven you've been meaning to fix! Load up NASCAR and note the wonderful calibration improvements! I can't say enuff good things about thrustmasters TECH SUPPORT folks but an instruction sheet would have been helpful :( Hope this helps....
an.. 14 Aug 1996#333524
>Can anyone please help me with instructions on how to change the steering >potentiometer in a T2. It seems to have a big barbed clip fixed in place >to hold it in position and I couldn't see how to remove it. Scott, I just redid mine too, it's a little tricky.. I'll try to remember how I did it best I can 1. Remove the steering wheel 2. Open the case 2a. remove the BASE of the unit from the face of the T-2 3. Remove the 4 screws that hold the "neck?" in place (these***are covered in the reddish 'locktite' substance) (the neck and bunjie cord and all is one assemby it wont fly (apart on you or anything) 4. take note of the wiring on the old potentiometer 5. DO NOT attempt to disassemble the bunjie cord setup leave that in place. 6. take a small screwdriver and place it behind the old "pentometer" <--short spelling :) 7. You need to take both hands, and pull on the round thingamajig the bunjie cord rolls on, by pulling on it you will lift the steering shaft up off of the old pentometer. 8. Then use your 3rd. hand <G> to GENTLY use the screwdriver to kind of 'pry' and I use THAT term loosly, to wiggle the old one out of place. Obviously you need to use extreme caution doing this if that bottom clip snaps off your in deep ka-ka! But the graphite like material that the assembly is composed of is pretty sturdy I wouldn't wanna chance it. 9. Make sure you CENTER the new pentometer before slipping it in there. To do this take the new one in your hand and "work" it thru it's full range of motion and get the feel of the total travel. then flip it upside down and notice the "slit" or "notch" in it, it should be parallel from top to bottom. it is now centered. 10. without knocking it out of proper alignment slip the new one back in there, I had to give mine a little nudge to pop it in there, but it didn't hurt anything. Notes: Resolder the new wires on the pentometer and dont get lazy and twist them on!! Do it right and Solder them it'll save you aggrivation later on. It's a good idea to "map" ALL the wiring in there before you s start I had one or two wires break loose from their soldering points while I tried to figure this puzzle out. This way at least you wont be "guessing" later. Before reassembly make sure you clean off all that red locktite off the threads. Re-apply a drop of loc-tite on each stud if you want. (loc-tite can be found at any reputable autoparts store and some 7-11's) Most of all ... BE PATIENT this will seem tedious but frustration leads to broken parts that end up next to the old joystick,keyboard and toaster oven you've been meaning to fix! Load up NASCAR and note the wonderful calibration improvements! I can't say enuff good things about thrustmasters TECH SUPPORT folks but an instruction sheet would have been helpful :( Hope this helps.... Andy A #58 Winsten Cup NASS 96 ***Comm Motorsports Homepage -------------------------------- http://www.***comm.net/~tomcat
Henrik Mon 14 Aug 1996#333525
On Aug 14, 1996 16:18:26 in article <Re: T2 Steering Potentiometer
Quoted text (72 lines)>>Can anyone please help me with instructions on how to change the steering >>potentiometer in a T2. It seems to have a big barbed clip fixed in place >>to hold it in position and I couldn't see how to remove it. >Scott, >I just redid mine too, it's a little tricky.. >I'll try to remember how I did it best I can >1. Remove the steering wheel >2. Open the case >2a. remove the BASE of the unit from the face of the T-2 >3. Remove the 4 screws that hold the "neck?" in place >(these***are covered in the reddish 'locktite' substance) >(the neck and bunjie cord and all is one assemby it wont fly >(apart on you or anything) >4. take note of the wiring on the old potentiometer >5. DO NOT attempt to disassemble the bunjie cord setup leave that in >place. >6. take a small screwdriver and place it behind the old >"pentometer" <--short spelling :) >7. You need to take both hands, and pull on the round thingamajig >the bunjie cord rolls on, by pulling on it you will lift the >steering shaft up off of the old pentometer. >8. Then use your 3rd. hand <G> to GENTLY use the screwdriver to >kind of 'pry' and I use THAT term loosly, to wiggle the old one >out of place. Obviously you need to use extreme caution doing >this if that bottom clip snaps off your in deep ka-ka! But the >graphite like material that the assembly is composed of is pretty >sturdy I wouldn't wanna chance it. >9. Make sure you CENTER the new pentometer before slipping it in >there. To do this take the new one in your hand and "work" it >thru it's full range of motion and get the feel of the total >travel. then flip it upside down and notice the "slit" or "notch" >in it, it should be parallel from top to bottom. it is now >centered. >10. without knocking it out of proper alignment slip the new one back >in there, I had to give mine a little nudge to pop it in there, >but it didn't hurt anything. >Notes: >Resolder the new wires on the pentometer and dont get lazy and >twist them on!! Do it right and Solder them it'll save you >aggrivation later on. >It's a good idea to "map" ALL the wiring in there before you s >start I had one or two wires break loose from their soldering >points while I tried to figure this puzzle out. This way at >least you wont be "guessing" later. >Before reassembly make sure you clean off all that red locktite >off the threads. Re-apply a drop of loc-tite on each stud if you >want. (loc-tite can be found at any reputable autoparts store >and some 7-11's) >Most of all ... BE PATIENT this will seem tedious but frustration >leads to broken parts that end up next to the old >joystick,keyboard and toaster oven you've been meaning to fix! >Load up NASCAR and note the wonderful calibration improvements! >I can't say enuff good things about thrustmasters TECH SUPPORT >folks but an instruction sheet would have been helpful :( >Hope this helps.... >Andy A >#58 Winsten Cup NASS 96 >***Comm Motorsports Homepage >-------------------------------- >http://www.***comm.net/~tomcat
I've had my T2 for quite awhile, and I've never had to replace my potentiometer. As most of you will notice, that over time with the T2, it begins to start "twitching". I'm guessing this is because dirt and residue get into it, and since it's so sensititive, it begins to corrode and do that annoying "twich". This little twich used to cost me races. I would be on the straight at Michigan, and then a little turn of the wheel (I had to correct the steering) and I was put into the wall because of THE "twich". There is a simple solution to this problem... Just go out to your local hardware store, or Radio Shack and pick up a can of spray, similar to WD40, but it should be an electronic degreaser. If it does not mention anything about this make sure it says "formulated to clean sensitive electronics, etc.", or something like that. It is also important that you get a spray that doesnt attract dust, or else you'll end up spraying the potentio every day. Try to get a spray that almosts evaoporates when its sprayed on something. If your alowwed to, try to spray a little on your finger and see what happens. If it does these three things - - Cleans sensitive electronic parts - Cleans WITHOUT attracting dust or any of that ***(important) - Evaporates (kinda) on contact with something (if it does this, it most likely wont attract dust) When you got that, go home, take the cover off the steering console of your T2, and then spray a little bit in the slot of the potentiometer. After this, begin steering the wheel around so that it "lubricates" the inner part of the potentio. Then, just repeat this step to your liking, put the cover back on your T2, and your done! load up your favorite SIM, and all is well. Should this procedure work (dont worry, it will) you wont have to do it again for quite awhile. I did this to mine atleast two weeks ago, and its fine, and I havent noticed a thing. Hope this helps... ;-) [Henrik Monti] [IndyBound Karting] [F1-Kart Speedway Miami, FL] [IVGA#2542, Int. Tool Racing-------------------------------/ \ / \----------------------------------------------------------------/
Rich McCab 14 Aug 1996#333526
I got the grinder out the first time. My next replacement didn't use the "clip". Rich Then I bought an Extreme CDS wheel..... > >Can anyone please help me with instructions on how to change the steering > >potentiometer in a T2. It seems to have a big barbed clip fixed in place > >to hold it in position and I couldn't see how to remove it. > >Thanks in advance, > >Scott I got the grinder out the first time. My next replacement didn't use the "clip".
Quoted text (11 lines)> Most of all ... BE PATIENT this will seem tedious but frustration > leads to broken parts that end up next to the old > joystick,keyboard and toaster oven you've been meaning to fix! > Load up NASCAR and note the wonderful calibration improvements! > I can't say enuff good things about thrustmasters TECH SUPPORT > folks but an instruction sheet would have been helpful :( > Hope this helps.... > hanks for the thorough response - I'll get my 3 hands to work on it
immediately :)

Sponsors

Affiliate Links

Sim Gaming Expo MOZA Racing Sim-Lab Fanatec TrakRacer Asetek Internet Privacy From NordVPN Dreamhost Capital One Credit Card Application Fanatical CDKeys Amazon Amazon UK Project Motor Racing iRacing Get your racing gloves, boots and more from Demon Tweeks. Enlist at Roberts Space Industries, developers of Star Citizen and Squadron 42


Back from the ashes since July, 2019. First created in 2001 with the merger of Legends Central (founded 1999) and simracing.dk.

A site by a sort of sim racer, for sim racers, about racing sims. News and information on both modern and historic sim racing software titles.

All products and licenses property of their respective owners.


Facebook Threads Bluesky Twitter Mastodon Instagram YouTube Tiktok Twitch Reddit Google News Apple News Subscribe via WordPress Flipboard eBay

Race Sim Central © 1999-2026 | Some links pay RSC a commission. Advertising does not equal endorsement.Cookie Policy