I received my PDPI L4 yesterday, installed it today, and now my jitter
problems are much more severe than they were with the gameport on my
Soundblaster Live. Has anyone had a negative experience with the PDPI?
A GPL wheel configuration question... In GPL if I use the 'Generic Driver'
the resolution of my wheel seems to be far greater than if I use the "Direct
Input" driver. The Generic Driver offers a value range of 5381-227211 on
Axis 0 while the Direct Input driver only offers a value range of 3-248. Do
the numbers returned indicate a greater sensitivity with the Generic Driver
or are the units of measurement simply different?
One other thing...When using the PDPI the Generic Driver is very jittery,
but the Direct Input driver is rock solid. Is Direct X doing some kind of
clean up on it's own, or does the Papy generic driver bypass the PDPI driver
thereby negating the advantages of the PDPI?
-Andrew
Thats odd, I just got my PDPI card Friday, installed that night with no
problem. I used to use the generic for GPL, but now I use the Directx
and after calibration my needles don't move at all, rock steady. I raced
a league race this morning and was rack steady, the car went where I
pointed it. The only drawback is I have to rework my setups to make up
for the PDPI accuracy!
Have you gone into control panel/joystick and made sure you have chosen
the PDPI card, not standard gamecard?
--
Richard "ZZ" Busch
Official member:
Screamers Racing League
Sim Racing Mag Honda Challenge
Sim Racing Mag F2 Ferrari
----------------
Busch Motorsports:
Remember racecar is racecar spelled backward
-----------------
Busch Carpentry:
Plans?, Oh, you mean that napkin sketch?
"Richard ZZ Busch" <[email hidden]> wrote in message
news:[email hidden]...
> Thats odd, I just got my PDPI card Friday, installed that night with no
> problem. I used to use the generic for GPL, but now I use the Directx
> and after calibration my needles don't move at all, rock steady. I raced
> a league race this morning and was rack steady, the car went where I
> pointed it. The only drawback is I have to rework my setups to make up
> for the PDPI accuracy!
Using the Direct Input driver my needles are also rock steady. I have a
feeling that that when I select Direct Input then GPL is using the PDPI
drivers, and when I select Generic Driver then GPL is using the standard
gamecard drivers. I guess I will continue to use the Direct Input driver
from here on out.
What is the range of values that the GPL Direct Input driver is reporting
for you? I'm assuming that my 2-248 on axis 0 is about what I should be
seeing.
> Have you gone into control panel/joystick and made sure you have chosen
> the PDPI card, not standard gamecard?
You're referring to the "Advanced" tab under game controllers? If so, then
yes I do have PDPI selected.
Thanks for the reply.
-AndrewS
> What is the range of values that the GPL Direct Input driver is reporting
> for you? I'm assuming that my 2-248 on axis 0 is about what I should be
> seeing.I get 25 - 126 range for my steering, I forget what the others are right
now. I'll try to remember to look next time I recalibrate in GPL, which
shouldn't be very soon :)
--
Richard "ZZ" Busch
Official member:
Screamers Racing League
Sim Racing Mag Honda Challenge
Sim Racing Mag F2 Ferrari
----------------
Busch Motorsports:
Remember racecar is racecar spelled backward
-----------------
Busch Carpentry:
Plans?, Oh, you mean that napkin sketch?
Where did you guy's get your PDPI L4,
I can't get into there website, is there somewhere else I can purchase it?
Thank's
Buster
Yes to your last question. 256 is the maximum range with pdpi so 3-248
is very close to perfect.
In article <4X9_4.2474$[email hidden]>,
"AndrewS" <[email hidden]> wrote:
> I received my PDPI L4 yesterday, installed it today, and now my jitter
> problems are much more severe than they were with the gameport on my
> Soundblaster Live. Has anyone had a negative experience with thePDPI?
>
> A GPL wheel configuration question... In GPL if I use the 'GenericDriver'
> the resolution of my wheel seems to be far greater than if I usethe "Direct
> Input" driver. The Generic Driver offers a value range of 5381-227211 on
> Axis 0 while the Direct Input driver only offers a value range of 3-248. Do
> the numbers returned indicate a greater sensitivity with the GenericDriver
> or are the units of measurement simply different?
>
> One other thing...When using the PDPI the Generic Driver is veryjittery,
> but the Direct Input driver is rock solid. Is Direct X doing somekind of
> clean up on it's own, or does the Papy generic driver bypass the PDPIdriver
> thereby negating the advantages of the PDPI?
>
> -Andrew
>
>
Sent via Deja.com http://www.deja.com/
Before you buy.
0 - 255 is a typical reading for the PDPI with 100K pots, so your settings
are about right. You are right, when GPL uses the generic driver it polls
the joystick in "analogue" mode, thus the PDPI goes into "compatibility"
mode. To get the most out of the PDPI you sould be using DirectInput where
the drivers are optimised to use the PDPI in "digital" mode.
AndrewS <[email hidden]> wrote in message
news:Jge_4.1632$[email hidden]...
then
Quoted text (24 lines)
> > "Richard ZZ Busch" <[email hidden]> wrote in message > news:[email hidden]... > > Thats odd, I just got my PDPI card Friday, installed that night with no > > problem. I used to use the generic for GPL, but now I use the Directx > > and after calibration my needles don't move at all, rock steady. I raced > > a league race this morning and was rack steady, the car went where I > > pointed it. The only drawback is I have to rework my setups to make up > > for the PDPI accuracy! > > Using the Direct Input driver my needles are also rock steady. I have a > feeling that that when I select Direct Input then GPL is using the PDPI > drivers, and when I select Generic Driver then GPL is using the standard > gamecard drivers. I guess I will continue to use the Direct Input driver > from here on out. > > What is the range of values that the GPL Direct Input driver is reporting > for you? I'm assuming that my 2-248 on axis 0 is about what I should be > seeing. > > > Have you gone into control panel/joystick and made sure you have chosen > > the PDPI card, not standard gamecard? > > You're referring to the "Advanced" tab under game controllers? If so,Quoted text (10 lines)
> yes I do have PDPI selected. > > Thanks for the reply. > > -AndrewS > > > > >
Thank's, just ordered one.
Act Labs was taking orders via telephone. Not sure if they still are.
www.act-labs.com
In article <[email hidden]>,
[email hidden] (BP astro 7) wrote:
> Where did you guy's get your PDPI L4,
> I can't get into there website, is there somewhere else I canpurchase it?
> Thank's
>
> Buster
>
Sent via Deja.com http://www.deja.com/
Before you buy.
Here's a copy of the email act-labs sent me after my order through PDPI
went south. They couldn't keep up so they turned it over to act-labs. You
won't find the info on the act-labs site for the reason stated below. Hope
this helps. With shipping, it's 68.00
Bob
Dear L4/PDPI Customer,
Thank you for your continued patience. Please note that ACT LABS is now
handling orders for ACT LABS RS wheels, ACT LABS PDPI cartridges and
PDPI cards. We now have stock and will begin shipping next week.
Due to our agreements with Visa, Mastercard and American Express, we are
not able to "re-activate" your previous order that was placed with PDPI.
If you have not yet placed your order with ACT LABS, please do so at:
www.actlab.com/pdpi_l4.htm
to replace your order. Please note that our agreement with PDPI does not
allow for us to provide access to this link to the public, so you must
use this link to access the PDPI order form.
If you love all driving games, please note that you can also purchase
cartridges that will enable use with the Sony Playstation and Nintendo 64.
Orders
ACT LABS
www.act-labs.com
PS: Please note that these PDPI products are available in very limited
quantities. They will be filled on a first-come-first-served basis.
PS: In order to ensure that we are able to respond to all our clients'
e-mail inquiries in a timely manner, our responses may seem short.
Thank you for your understanding
[email hidden] wrote:
Quoted text (15 lines)
> Act Labs was taking orders via telephone. Not sure if they still are. > www.act-labs.com > > In article <[email hidden]>, > [email hidden] (BP astro 7) wrote: > > Where did you guy's get your PDPI L4, > > I can't get into there website, is there somewhere else I can > purchase it? > > Thank's > > > > Buster > > > > Sent via Deja.com http://www.deja.com/ > Before you buy.Thank's, just ordered one.
"BP astro 7" <[email hidden]> wrote in message
news:[email hidden]...
>
> Thank's, just ordered one.
You can find the info at Actlabs site for the PDPI card here.
http://www.actlab.com/pdpi_l4.htm


































