Help!!!!Nascar Pro Racing Wheel wires came off circuit board TIA

Hello,The board has six pins.And there is seven wires.three wires come from the connector to the board left top is blue,middle is red and the bottom is yellow. Coming from the wheel white,orange,green,and blue.Can someone tell me where they go? Thanks for your help. [email hidden] Remove spam Mike -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 80,000 Newsgroups - 16 Different Servers! =-----

"BigMac" <[email hidden]> ...

Quoted text (8 lines)

> Hello,The board has six pins.And there is seven wires.three wires come > from the connector to the board left top is blue,middle is red and > the bottom is yellow. Coming from the wheel white,orange,green,and > blue.Can someone tell me where they go? Thanks for your help. > [email hidden] > Remove spam > > Mike

May I be the first to say it - DON'T POST BINARIES TO THIS NG. See alt.binaries.simulators.autos -- Tony Whitley GPLRank +10.90

On Wed, 3 Jan 2001 14:36:00 -0000, "Tony Whitley" <t o n y . w h i t l e y @ nStPlAwMorld.com> wrote:

Quoted text (13 lines)

> >"BigMac" <[email hidden]> ... >> Hello,The board has six pins.And there is seven wires.three wires come >> from the connector to the board left top is blue,middle is red and >> the bottom is yellow. Coming from the wheel white,orange,green,and >> blue.Can someone tell me where they go? Thanks for your help. >> [email hidden] >> Remove spam >> >> Mike > >May I be the first to say it - DON'T POST BINARIES TO THIS NG. See >alt.binaries.simulators.autos

Huh? He didn't post any binaries.. Andre >-- >Tony Whitley >GPLRank +10.90 > > >

Andre Warringa <[email hidden]> wrote in message news:[email hidden]... > Huh? He didn't post any binaries.. > Andre Oh yes he did.... They have probably just not been accepted by your newsserver.

On Wed, 3 Jan 2001 16:46:01 +0100, "Mikkel Gram-Hansen" <[email hidden]> wrote:

Quoted text (8 lines)

>Andre Warringa <[email hidden]> wrote in message >news:[email hidden]... > >> Huh? He didn't post any binaries.. >> Andre > >Oh yes he did.... They have probably just not been accepted by your >newsserver.

You're right, I saw the reply from Olav later. Andre

red to green, yellow to black and blew to bits!!!!!!

First, you need to connect blue and white together. After that is good, connect red orange and green together. Finally, since it came apart, I can only see that you can connect the two blue wires by drilling through the first blue wire with a very small drill, less then .005 mm's wide or with a lead pencil. When all of this is done, you have to manually remove the circuit board and pot from the wheel, neither are needed any more and the best use for them is in the trash can. This is the important part, even if wires are connected to the pot or circuit board, these are not needed, you only need the wires to touch each other with one touching the plastic and the other touching the wire. Hope this helps. -- -Stuart Becktell "But in a way, fear is a big part of racing, because if there was nothing to be frightened of and no limit, any fool could get into a motor car, and racing would not exist as a sport." - Jim Clark '62 and '65 World F1 Champion and Indy 500 Champion "BigMac" <[email hidden]> wrote in message news:[email hidden]... > Hello,The board has six pins.And there is seven wires.three wires come > from the connector to the board left top is blue,middle is red and > the bottom is yellow. Coming from the wheel white,orange,green,and > blue.Can someone tell me where they go? Thanks for your help. > [email hidden] > Remove spam > > Mike > > > -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- > http://www.newsfeeds.com - The #1 Newsgroup Service in the World! > -----== Over 80,000 Newsgroups - 16 Different Servers! =-----