Race Sim Central
Rec.Autos.Simulators Archive

Car physics; camber units in Pacejka Fx formula

12 posts by 5 people · 04 Mar 2002 17:28 UTC - 08 Mar 2002 13:34 UTC

Ruud van Gaal 04 Mar 2002 17:28 UTC#132229
Hi all, After introducing camber to my tire force system, the standard Ferrari Pacejka parameter set from Genta's book makes it slide sideways severely. The camber is very much near 0, but even a little degree of camber makes things go haywire). I was wondering if anybody knew the exact units that 'camber' uses in Pacejka's Fx formula? I now use radians, but with a5/a8/a111/a112 set as they're specified, I get LARGE forces developing quickly. Thanks, Ruud van Gaal Free car sim: http://www.racer.nl/ Pencil art : http://www.marketgraph.nl/gallery/
"Ruud van Gaal" <[email hidden]> wrote in message news:[email hidden]...
Quoted text (12 lines)> Hi all, > > After introducing camber to my tire force system, the standard Ferrari > Pacejka parameter set from Genta's book makes it slide sideways > severely. > The camber is very much near 0, but even a little degree of camber > makes things go haywire). I was wondering if anybody knew the exact > units that 'camber' uses in Pacejka's Fx formula? > > I now use radians, but with a5/a8/a111/a112 set as they're specified, > I get LARGE forces developing quickly. >
Ruud, The short answer, I just dont know. Even with zero camber a side force is produced. I dont understand it. How can that be true at rest? It must be a result of the formula being empirical, it tries to fit the curve for most situations, but fails a little. I can understand that a force would be produced due to conicity and camber at higher speed. Ash http://www.siroccoracing.com
On Tue, 5 Mar 2002 11:10:56 -0000, "Ashley McConnell" <[email hidden]> wrote:
Quoted text (10 lines)>"Ruud van Gaal" <[email hidden]> wrote in message >news:[email hidden]... >> I was wondering if anybody knew the exact >> units that 'camber' uses in Pacejka's Fx formula? >> >> I now use radians, but with a5/a8/a111/a112 set as they're specified, >> I get LARGE forces developing quickly. > >The short answer, I just dont know. Even with zero camber a side force is >produced. I dont understand it. How can that be true at rest?
In that case, you'd expect slip angle to get back to 0, but indeed, it looks like Pacejka's Fx formula doesn't work nicely at 0 speed (because with the same conicity/camber at speeds>0 a force would be developed, where speed isn't an input even). Perhaps nearing 0 speed some cutoff must be done to get Sv and Sh down to 0. Just for some better low-speed behavior. Ruud van Gaal Free car sim: http://www.racer.nl/ Pencil art : http://www.marketgraph.nl/gallery/
Im using degrees here to pass into pacejka...I guess the information was on Genta's...wansnt it? And Im not getting a lot of lateral force...the force Im getting is so low that Im still guessing if my signs are right or not... The Ferrari on the book as a "static" camber force applied to the constants...maybe some kind of non-symmetry in the tires? I dont trust those values anyway... "Ashley McConnell" <[email hidden]> wrote in message news:<a629cd$ie7$[email hidden]>...
Quoted text (26 lines)> "Ruud van Gaal" <[email hidden]> wrote in message > news:[email hidden]... > > Hi all, > > > > After introducing camber to my tire force system, the standard Ferrari > > Pacejka parameter set from Genta's book makes it slide sideways > > severely. > > The camber is very much near 0, but even a little degree of camber > > makes things go haywire). I was wondering if anybody knew the exact > > units that 'camber' uses in Pacejka's Fx formula? > > > > I now use radians, but with a5/a8/a111/a112 set as they're specified, > > I get LARGE forces developing quickly. > > > > > Ruud, > > The short answer, I just dont know. Even with zero camber a side force is > produced. I dont understand it. How can that be true at rest? It must be > a result of the formula being empirical, it tries to fit the curve for most > situations, but fails a little. I can understand that a force would be > produced due to conicity and camber at higher speed. > > Ash > http://www.siroccoracing.com
"Stefano Casillo" <[email hidden]> wrote in message news:[email hidden]...
Quoted text (10 lines)> Im using degrees here to pass into pacejka...I guess the information > was on Genta's...wansnt it? And Im not getting a lot of lateral > force...the force Im getting is so low that Im still guessing if my > signs are right or not... > > The Ferrari on the book as a "static" camber force applied to the > constants...maybe some kind of non-symmetry in the tires? I dont trust > those values anyway... > >
Hi Stefano, Yep its Genta we are talking about. Are you sure you are setting the Fz value to the correct amount. I discovered last night that I was using mass / 4000 (instead of (mass * g)/4000). This created Fy values of around 300N max. Remember Fz is in KN. Also, make sure your slipangle is in degrees rather than radians. What I found was helpful was to create a "graphing" application to produce graphs using the code you have used for Pacekja. Have a look at "physics" on my website for an example of a graph. Once you have it working in the graph application, you can move it over to your sim (something I have done recently). The tyres produce a lateral force with no slipangle or slipratio, my feeling is that this should be linked to speed a little (but I am only learning too, so dont take my word for it :)). This force is produced by conicity (i.e. one side of the tyre is slightly larger in diameter than the other) or plysteer (due to the construction of the tyre). You probably know this stuff already, but I hope it helps All the best, Ash http://www.siroccoracing.com
Ruud, I thought u were using a correction at low speed for tire force due to relaxation... shouldnt that bring everthing to 0 when your speed is 0? Ashley??? What's 4000 in your code???? Magic numbers or what??? [email hidden] (Ruud van Gaal) wrote in message news:<[email hidden]>...
Quoted text (25 lines)> On Tue, 5 Mar 2002 11:10:56 -0000, "Ashley McConnell" > <[email hidden]> wrote: > > >"Ruud van Gaal" <[email hidden]> wrote in message > >news:[email hidden]... > >> I was wondering if anybody knew the exact > >> units that 'camber' uses in Pacejka's Fx formula? > >> > >> I now use radians, but with a5/a8/a111/a112 set as they're specified, > >> I get LARGE forces developing quickly. > > > >The short answer, I just dont know. Even with zero camber a side force is > >produced. I dont understand it. How can that be true at rest? > > In that case, you'd expect slip angle to get back to 0, but indeed, it > looks like Pacejka's Fx formula doesn't work nicely at 0 speed > (because with the same conicity/camber at speeds>0 a force would be > developed, where speed isn't an input even). > Perhaps nearing 0 speed some cutoff must be done to get Sv and Sh down > to 0. Just for some better low-speed behavior. > > > Ruud van Gaal > Free car sim: http://www.racer.nl/ > Pencil art : http://www.marketgraph.nl/gallery/
"Stefano Casillo" <[email hidden]> wrote in message news:[email hidden]...
Quoted text (7 lines)> Ruud, > > I thought u were using a correction at low speed for tire force due to > relaxation... shouldnt that bring everthing to 0 when your speed is 0? > > Ashley??? What's 4000 in your code???? Magic numbers or what??? >
Nope, not quite magic ;) I havent got any weight distribution or suspension yet, so I just divide the weight by 4 to get the weight on each wheel. But the Pacekja formula needs Fz in kiloNewtons (kN) so you need to divide that AGAIN by 1000, so I just combined the 2 divisions. Nothing mystical at all ;) All the best, Ash http://www.siroccoracing.com
On 5 Mar 2002 09:10:27 -0800, [email hidden] (Stefano Casillo) wrote: >Ruud, > >I thought u were using a correction at low speed for tire force due to >relaxation... shouldnt that bring everthing to 0 when your speed is 0? I use relaxation currently only longitudinally. Laterally the car at low speed gets very jittery lateral forces, which if integrated at high enough frequency, make the car seem stable, even sideways at hills and such. So I guess maybe with the camber forces, left & right tires will balance eachother out. But nearing 0, it's just the slipangle and slipratio that get 'relaxed' and stabilize. They may stabilize at non-zero values though when a static camber force creeps in, I don't know. The problem I had was with Genta numbers the lateral forces with a bit of camber became really large, and my car moved over to the side very unrealistically, to make an understatement. :) Ruud van Gaal Free car sim: http://www.racer.nl/ Pencil art : http://www.marketgraph.nl/gallery/
Left and right wont balance at all...cause if u are using a non-zero value for a9 in pacejka lateral formula u'll get a constant lateral accelleration... U could try to invert a9 on the left tires...but that doesnt make much sense...I think that a9 means that that tire tends to steer somewhere left or right...and that's possible...but, that'll work only if the tire is rolling...dont u think? In Gillespie there's a graph of lateral force "building" up while the tire is rolling...I still didnt code my low-speed behavior, but I think I'll start from that graph to come up with something... Anyway...if u are getting a lot of camber thrust there's something wrong somewhere cause I think in Milliken I've read that camber thrust isnt very relevant over the total force... Meanwhile...I know u have this figured out so: any suggestion for papers, books, links about differentials? Nothing in Genta, nothing in Gillespie, something in Milliken, and not enough on the internet... I've ordered a Carroll Smith book on amazon and it should have something about differentials...but it's going to be a 1-2 week waiting...and Im locked with a LOCKED differential... [email hidden] (Ruud van Gaal) wrote in message news:<[email hidden]>...
Quoted text (25 lines)> On 5 Mar 2002 09:10:27 -0800, [email hidden] (Stefano Casillo) wrote: > > >Ruud, > > > >I thought u were using a correction at low speed for tire force due to > >relaxation... shouldnt that bring everthing to 0 when your speed is 0? > > I use relaxation currently only longitudinally. Laterally the car at > low speed gets very jittery lateral forces, which if integrated at > high enough frequency, make the car seem stable, even sideways at > hills and such. > So I guess maybe with the camber forces, left & right tires will > balance eachother out. But nearing 0, it's just the slipangle and > slipratio that get 'relaxed' and stabilize. They may stabilize at > non-zero values though when a static camber force creeps in, I don't > know. > > The problem I had was with Genta numbers the lateral forces with a bit > of camber became really large, and my car moved over to the side very > unrealistically, to make an understatement. :) > > > Ruud van Gaal > Free car sim: http://www.racer.nl/ > Pencil art : http://www.marketgraph.nl/gallery/
On 6 Mar 2002 07:39:53 -0800, [email hidden] (Stefano Casillo) wrote: >In Gillespie there's a graph of lateral force "building" up while the >tire is rolling...I still didnt code my low-speed behavior, but I >think I'll start from that graph to come up with something... i think you 've got a point here, the tire act like a rubber's block when not rolling, i.e. you should compute a friction force instead of using pacejka formula if v=0 then f = k0 else f = -k1.v Sebastien TIXIER - Game Developer Dynamics and Car Physics http://www.eden-studios.fr GPLRank Normal:-44.24 Monster:-124.44
>if v=0 then f = k0 else f = -k1.v BIG mistake,in fact its if v=0 then f=k0.tire_load else f= -k1.tire_load.v/||v|| when v is not null the friction force is proportional to the load on the tire and opposite to the velocity direction. when v is null it's the minimun force to apply on the solid to start it to move.
>> The camber is very much near 0, but even a little degree of camber >> makes things go haywire). I was wondering if anybody knew the exact >> units that 'camber' uses in Pacejka's Fx formula? >> Ruud, I tested the latest alpha release on my game box, and the car would not even start at Carrera, just slid sideways to the left all the way into the pit wall.... is this "bug" related to the above problem? uwe

Sponsors

Affiliate Links

Sim Gaming Expo MOZA Racing Sim-Lab Fanatec TrakRacer Asetek Internet Privacy From NordVPN Dreamhost Capital One Credit Card Application Fanatical CDKeys Amazon Amazon UK Project Motor Racing iRacing Get your racing gloves, boots and more from Demon Tweeks. Enlist at Roberts Space Industries, developers of Star Citizen and Squadron 42


Back from the ashes since July, 2019. First created in 2001 with the merger of Legends Central (founded 1999) and simracing.dk.

A site by a sort of sim racer, for sim racers, about racing sims. News and information on both modern and historic sim racing software titles.

All products and licenses property of their respective owners.


Facebook Threads Bluesky Twitter Mastodon Instagram YouTube Tiktok Twitch Reddit Google News Apple News Subscribe via WordPress Flipboard eBay

Race Sim Central © 1999-2026 | Some links pay RSC a commission. Advertising does not equal endorsement.Cookie Policy